Fidelity Measurement AFM18 Operation Manual Download Page 11

Page: 11 / 78

www.fi-measurement.com

20. NET INDICATOR

Visible when the tare function is in effect. Weight reading shown is net value.

21. GROSS INDICATOR

Visible when gross weight reading is displayed.

22. STABLE INDICATOR

Visible when weight reading is stable.

23. ZERO INDICATOR

Visible when instrument is at true zero weight status.

24. CAPACITY TRACK BAR

The ratio (increment = 10%) of applied & remaining weighing capacities are

shown here.

25. WEIGHT UNITS AND FUNCTIONS

•

% = Percentage (when Percentage Mode in function),

•

kg = kilogram,

•

PCS = Pieces (when Piece Count Mode in function),

•

kg/PCS and g/PCS = Weight per piece (when Piece Count Mode in

function),

•

lb = pound.

26. CHARGE STATUS INDICATOR

•

Red color: Recharging battery,

•

Green color: Charging completed.

Summary of Contents for AFM18















































































Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands

Fidelity Measurement AFM18, Operation Manual

Search results

Summary of Contents for AFM18

Reviews:

Brands by name

Popular brands