manualshive.com logo in svg

Fibocom L860-GL, At Command User Manual, Page: 92 / 254

Share
Download
Fibocom L860-GL At Command User Manual Download Page 92

 

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved. 

FIBOCOM L860 AT Commands User Manual   

 

 

 

 

 

 

 

 

 

 

Page 92 of 254 

 

6.1.12 +CDSI, Unsolicited Response (New SMS-STATUS-REPORT 

Indication) 

The +CDSI unsolicited response is sent to the TE upon receipt of a new SMS-STATUS-REPORT SMS, if 

the +CNMI parameter <ds> is set to ‘2’.   

This unsolicited message indicates that a new SMS-STATUS-REPORT message was received, and is 

stored in location <index>. 

Unsolicited Response 

+CDSI: <mem>,<index> 

Command 

Description 

Set 

N/A 

Read 

N/A 

Test 

N/A 

Parameters 

<mem>  Message memory space. "SR" - status report storage. 

<index>  Location of the new message. 

Example 

AT+CMGF=1 

OK 

AT+CSMP=49,165    /*Set Message type to Status Report, see +CMGW*/ 

OK 

AT+CSMP? 

+CSMP: 49,167,0,0 

OK 

AT+CNMI=1,0,0,2 

OK 

AT+CMGS="052468000" 

> Hello 

+CMGS: 188 

OK 

+CDSI: "SR",1 

 

6.1.13 +CDS, Unsolicited Response (New SMS-STATUS-REPORT 

Receipt) 

The +CDS unsolicited response is sent to the TE upon receipt of a new mobile-terminated SMS if the 

+CNMI parameter <ds> is set to ‘1’.   

Summary of Contents for L860-GL































































































































































































































































Reviews:

No comments