manualshive.com logo in svg

Fibocom L860-GL, At Command User Manual, Page: 49 / 254

Share
Download
Fibocom L860-GL At Command User Manual Download Page 49

 

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved. 

FIBOCOM L860 AT Commands User Manual   

 

 

 

 

 

 

 

 

 

 

Page 49 of 254 

The parameter will be saved in NVM and can restore at power cycle. 

Command 

Description 

Set 

[Function] 

Enable/Disable SIM card hot plug 
 

[Syntax] 

AT+MSMPD=< status> 
 

[Response/Action] 

OK 

Or:   

+CME ERROR: <err> 

Read 

[Function] 

Read the current status 
 

[Syntax] 

AT+MSMPD? 
 

[Response/Action] 

+MSMPD: <status> 

OK 

Test 

[Function] 

Return the list of supported value. 
 

[Syntax] 

AT+MSMPD=? 
 

[Response/Action] 

+MSMPD: <list of supported status> 

OK 

Parameters 

<status>  

0: Disable the SIM card hot plug feature 

1: Enable the SIM card hot plug feature 

The default value is 1 

Example 

AT+MSMPD=? 

+MSMPD: (0,1) 
 

Summary of Contents for L860-GL































































































































































































































































Reviews:

No comments