Fibocom L860-GL Page 45 At Command User Manual Download

Page: 45 / 254

FIBOCOM L860 AT Commands User Manual

Page 45 of 254

Command

Description

[Syntax]

AT+CSIM=?

[Response/Action]

Parameters

length

integer type; length of the characters that are sent to TE in

command

response

command

command passed on by MT to SIM in hex format

response

response to the command passed on by the SIM to the MT

Example

Reference

3GPP TS 27.007

4.2 Other Parameter Commands

4.2.1 +CFUN, Set Phone Functionality

This command set the phone functionality.

Command

Description

Set

[Function]

The Set command selects the level of functionality <fun> in the modem.

[Syntax]

AT+CFUN=<fun>[,<rst>]

[Response/Action]

+CME ERROR: <err>

Read

[Function]

The Read command displays the current level of functionality.

Summary of Contents for L860-GL































































































































































































































































Search results

Summary of Contents for L860-GL

Reviews:

Related manuals for L860-GL

Brands by name

Popular brands

Fibocom L860-GL, At Command User Manual

Search results

Summary of Contents for L860-GL

Reviews:

Related manuals for L860-GL

Brands by name

Popular brands