Fibocom L860-GL Page 82 At Command User Manual Download

Page: 82 / 254

FIBOCOM L860 AT Commands User Manual

Page 82 of 254

Command

Description

AT+CMGR=160// SMS-SUBMIT

+CMGR: "STO UNSENT","0544565034",

ABC

AT+CSDH=1

AT+CMGR=160

+CMGR: "STO UNSENT","0544565034",,81,29,0,0,"04/11/04,09: 48:

36+08","+97254120032",145,3

ABC

Reference

3GPP TS 27.005

6.1.7 +CNMI, New Message Indications to Terminal

This command handles enabling of unsolicited notifications to the terminal when an SMS is received by

the Modem.

After sending an unsolicited response to the TE, the Modem will expect a +CNMA (new message

acknowledgement) from the TE within a predefined timeout of 15 seconds. Within the timeout the Modem

will not send another unsolicited response to the TE before the previous one is acknowledgement. If the

Modem does not receive acknowledgment within the required time, CNMI parameters will NOT be reset

automatically and the unsolicited response will send to the TE again.

Command

Description

Set

[Function]

This command handles enabling of unsolicited notifications to the terminal when an

SMS is received by the Modem.

[Syntax]

AT+CNMI=[<mode>[,<mt>[,<bm>[,<ds>[,<bfr>]]]]]

[Response/Action]

or:

+CME ERROR: <err>

Read

[Function]

Summary of Contents for L860-GL































































































































































































































































Search results

Summary of Contents for L860-GL

Reviews:

Related manuals for L860-GL

Brands by name

Popular brands

Fibocom L860-GL, At Command User Manual

Search results

Summary of Contents for L860-GL

Reviews:

Related manuals for L860-GL

Brands by name

Popular brands