Fibocom L860-GL At Command User Manual Download Page 215

Page: 215 / 254

FIBOCOM L860 AT Commands User Manual

Page 215 of 254

Command

Description

3 background

subscribed value

If the Traffic class is specified as conversational or streaming, then the Guaranteed

and Maximum bit rate parameters should also be provided. Other values are reserved.

A numeric parameter that indicates the maximum number

of kbits/s delivered to UMTS (up-link traffic) at a SAP. As an example a bit rate of 32

kbit/s would be specified as ‘32’ (e.g. AT+CGEQREQ=…,32, …). This parameter

should be provided if the Traffic class is specified as conversational or streaming (refer

3GPP TS 24.008 subclause 10.5.6.5).

A numeric parameter that indicates the maximum number

of kbits/s delivered by UMTS (down-link traffic) at a SAP. As an example a bit rate of

32 kbit/s would be specified as ‘32’ (e.g. AT+CGEQREQ=…,32, …). If the parameter is

set to ‘0’ the subscribed value will be requested. This parameter should be provided if

the Traffic class is specified as conversational or streaming (refer 3GPP TS 24.008

subclause 10.5.6.5).

<Guaranteed bit rate UL> A numeric parameter that indicates the guaranteed number

of kbits/s delivered to UMTS (up-link traffic) at a SAP (provided that there is data to

deliver). As an example a bit rate of 32kbit/s would be specified as ‘32’ (e.g.

AT+CGEQREQ=…,32, …). If the parameter is set to ‘0’ the subscribed value will be

requested. This parameter should be provided if the Traffic class is specified as

conversational or streaming (refer 3GPP TS 24.008 subclause 10.5.6.5).

<Guaranteed bit rate DL> A numeric parameter that indicates the guaranteed number

of kbits/s delivered by UMTS (down-link traffic) at a SAP (provided that there is data to

deliver). As an example a bit rate of 32kbit/s would be specified as ‘32’ (e.g.

AT+CGEQREQ=…,32, …). If the parameter is set to ‘0’ the subscribed value will be

requested. This parameter should be provided if the Traffic class is specified as

conversational or streaming (refer 3GPP TS 24.008 subclause 10.5.6.5).

<Delivery order> A numeric parameter that indicates whether the UMTS bearer shall

provide in-sequence SDU delivery or not.

0 no

1 yes

2 subscribed value.

Other values are reserved.

Summary of Contents for L860-GL































































































































































































































































Search results

Summary of Contents for L860-GL

Reviews:

Fibocom L860-GL, At Command User Manual, Page: 215 / 254

Search results

Summary of Contents for L860-GL

Reviews: