manualshive.com logo in svg

Fibocom L860-GL, At Command User Manual, Page: 56 / 254

Share
Download
Fibocom L860-GL At Command User Manual Download Page 56

 

Reproduction forbidden without Fibocom Wireless Inc. written authorization – All Rights Reserved. 

FIBOCOM L860 AT Commands User Manual   

 

 

 

 

 

 

 

 

 

 

Page 56 of 254 

Command 

Description 

 

[Syntax] 

AT+MSTART? 
 

[Response/Action] 

+MSTART: <at start>,<sim ready> 

OK

 

Test 

[Function] 

This command returns the supported values. 
 

[Syntax] 

AT+MSTART=? 
 

[Response/Action] 

+MSTART: ((list of supported <at start>),(list of supported <sim read>)) 

OK

 

Parameters 

<at start> 
0:    Do not output “AT command ready” from UART 

1:    Output “AT command ready” from UART (default value) 

<sim ready> 
0:    Do not output “+SIM READY” after SIM init OK 

1:    Output “+SIM READY” after SIM init OK (default value) 

Notes

: 

“AT command ready” can not output from USB port even if set to 1. “+SIM 

READY” can output from UART and USB port according to setting. 

Example 

AT+MSTART=? 

+MSTART: (0-1,0-1) 

OK 

AT+MSTART=1,1 

OK 

AT+MSTART? 

+MSTART: 1,1 

OK 
 

 

Summary of Contents for L860-GL































































































































































































































































Reviews:

No comments