Fibocom L860-GL At Command User Manual Download Page 223

Page: 223 / 254

FIBOCOM L860 AT Commands User Manual

Page 223 of 254

Command

Description

NULL none, for PDP type OSP: IHOSS (Obsolete)

PPP Point-to-point protocol for a PDP such as IP

PAD character stream for X.25 character (triple X PAD) mode (Obsolete)

X25 X.25 L2 (LAPB) for X.25 packet mode (Obsolete).

M-OPT-PPP MS supports manufacturing specific protocol

M-HEX MS supports manufacturing specific protocol

M-RAW_IP MS supports manufacturing specific protocol.

<cid>

A numeric parameter which specifies a particular PDP context definition (see

the +CGDCONT and +CGDSCONT commands).

Example

AT+CGDATA=ppp

CONNECT

…….

……..

AT+CGDATA=?

+CGDATA: (PPP,M-OPT-PPP,M-HEX,M-RAW_IP,PAD,X25)

Reference

3GPP TS 27.007

11.2.16 +CGDSCONT

，

Define Secondary PDP Context

This command is used to define a secondary PDP context by specifying the PDP context parameter

values for a <cid> (local context identification parameter). If the command is used only with the one

parameter <cid>, it means that the corresponding PDP context becomes undefined.

Command

Description

Set

[Function]

Set command specifies PDP context parameter values for a Secondary PDP context

identified by the (local) context identification parameter, <cid>.

[Syntax]

AT+CGDSCONT=[<cid>, <p_cid> [,<d_comp>[,<h_comp>

[,<IM_CN_Signaling_Flag_Ind>]

]]]

[Response/Action]

Summary of Contents for L860-GL































































































































































































































































Search results

Summary of Contents for L860-GL

Reviews:

Fibocom L860-GL, At Command User Manual, Page: 223 / 254

Search results

Summary of Contents for L860-GL

Reviews: