Fibocom L860-GL Page 193 At Command User Manual Download

Page: 193 / 254

FIBOCOM L860 AT Commands User Manual

Page 193 of 254

Command

Description

AT+CGDCONT?

+CGDCONT: 1,"IP","CMWAP","0.0.0.0",0,0

+CGDCONT: 2,"IP","CMNET","0.0.0.0",0,0

AT+CGACT=1

AT+CGDCONT?

+CGDCONT: 1,"IP","CMWAP","10.230.50.116",0,0

+CGDCONT: 2,"IP","CMNET","10.3.97.156",0,0

AT+CGDCONT=?

+CGDCONT: (1-20),"IP",,,(0),(0,1,2,3,4),(0,1),(0,1),(0,1),(0,1)

+CGDCONT: (1-20),"IPV6",,,(0),(0,1,2,3,4),(0,1),(0,1),(0,1),(0,1)

+CGDCONT: (1-20),"IPV4V6",,,(0),(0,1,2,3,4),(0,1),(0,1),(0,1),(0,1)

Reference

3GPP TS 27.007

11.2.3 +CGQMIN, Quality of Service Profile (Min Acceptable)

This command enables the terminal to specify the minimum acceptable profile which is checked by the

ME against the negotiated profile returned in the Activate PDP Context Accept message.

Command

Description

Set

[Function]

The Set command specifies a profile for the context identified by the (local) context

identification parameter,<cid>. As this is the same parameter that is used in the

+CGDCONT command, the +CGQMIN command is effectively an extension of the

+CGDCONT command. The QoS profile consists of a number of parameters, each of

which may be set to a separate value.

[Syntax]

AT+CGQMIN=<cid>[,<precedence>[,<delay>[,<reliability.>[,<peak>[,<mean>]]]]]

Summary of Contents for L860-GL































































































































































































































































Search results

Summary of Contents for L860-GL

Reviews:

Related manuals for L860-GL

Brands by name

Popular brands

Fibocom L860-GL, At Command User Manual

Search results

Summary of Contents for L860-GL

Reviews:

Related manuals for L860-GL

Brands by name

Popular brands