manualshive.com logo in svg

FE FRENIC-Mini, Instruction Manual

Share
Download
FE FRENIC-Mini Instruction Manual Download Page 147

 

5-70 

 

H04, H05 

Auto-reset (Times and Reset interval) 

 

H04 and H05 specify the auto-reset function that makes the inverter automatically attempt to 
reset the tripped state and restart without issuing an alarm (for any faults) even if any 
protective function subject to reset is activated and the inverter enters the forced-to-stop state 
(tripped state). 

If the protective function works in excess of the times specified by H04, the inverter will issue 
an alarm (for any faults) and not attempt to auto-reset the tripped state. 

Listed below are the recoverable alarm statuses to be retried. 

Alarm status 

LED monitor displays: 

Alarm status 

LED monitor displays: 

Overcurrent protection

0c1

, 

0c2

 or 

0c3

 Motor 

overheated 

0h4 

Overvoltage protection

0u1

, 

0u2

 or 

0u3

 Motor 

overloaded 

0l1 

 or 

0l2 

Heat sink overheated

0h1 

Inverter overloaded

0lu 

Braking resistor 
overheated 

dbh 

 

 

 

„

 Number of reset times (H04) 

H04 specifies the number of reset times for the inverter to automatically attempt to escape 
from the tripped state. When H04 = 0, the auto-reset function will not be activated. 

 

If the "auto-reset" function has been specified, the inverter may automatically restart and run the 
motor stopped due to a trip fault, depending on the cause of the tripping. 

Design the machinery so that human body and peripheral equipment safety is ensured even 
when the auto-resetting succeeds. 

Otherwise an accident could occur. 

 

„

 Reset interval (H05) 

After the reset interval specified by H05 from when the inverter enters the tripped state, it 
issues a reset command to auto-reset the tripped state. Refer to the timing scheme diagram 
below. 

<Timing scheme for failed retry (No. of reset times: 3)> 

 

The auto-reset operation can be monitored from the external equipment by assigning the 
digital output signal TRY to any of the programmable output terminals [Y1] and [30A/B/C] with 
E20 or E27 (data = 26). 

Summary of Contents for FRENIC-Mini



























































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands