manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 94 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 94

Operation

4812164601_C.pdf

2023-01-05

Vibration

Manual/Automatic vibration

20

Fig.  Instrument panel
 20. Switch, Vibration selector

In 

Working mode/Vibration

 (20) (LED LEFT lit), you

can manually activate vibration on the forward drum
using button 1 on the forward/reverse lever.

In automatic mode, the vibration is activated when the
preset speed is reached, provided that the drum is
selected with the help of the buttons on the control
lever.

(See the Display chapter to active).

Vibration is automatically deactivated when the lowest
pre-set speed is reached.

Deactivation is done by pressing button 1 again.

The machine is
equipped with
options

Standard equipped
machine

Fig. Right Forward/Reverse lever

1

2

1

If the machine is in Transport mode and the
buttons on the forward/reverse lever are pressed,
the Working mode symbol is shown on the
display.
The three LEDs on the Working position button
flash.

If the machine is in Transport mode and the
buttons on the forward/reverse lever are pressed,
the Working mode symbol is shown on the
display.
The three LEDs on the Working position button
flash.

78

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments