Fayat DYNAPAC CC1400C Instruction Manual Download Page 79

Page: 79 / 239

Machine description

4812164601_C.pdf

2023-01-05

Fuses at battery master disconnect switch

The figure shows the different positions of the fuses in
the engine compartment.

The table below gives fuse amperage and function.
All fuses are flat pin fuses.

Fig. Battery disconnector and fuses
(D1703 / V2203-M-E3B)

D1703 / V2203-M-E3B (Stage IIIA)

Main fuse

40A

Main fuse

40A

F14

Glowing, Start relay, Fuel
solenoid

50A

F14

Glowing, Start relay, Fuel
solenoid

50A

Fig. Master switch and fuses (D1803 /
V2403-CR-E4B / V2403-CR-E5B)

D1803 / V2403-CR-E4B (Tier 4f) /
V2403-CR-E5B (Stage V)

Main fuse

40A

Main fuse

40A

F13

Engine ECU

50A

F13

Engine ECU

50A

F14

Starting

50A

F14

Starting

50A

F20

Glowing

50A

F20

Glowing

50A

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Search results

Summary of Contents for DYNAPAC CC1400C

Reviews:

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 79 / 239

Search results

Summary of Contents for DYNAPAC CC1400C

Reviews: