manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 52 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 52

Machine description

4812164601_C.pdf

2023-01-05

4700903459
Warning - Read instruction manual

The operator must read the safety, operation and
maintenance instructions before operating the
machine.

4700904083
Warning - Edge cutter (optional)

Warning of rotating parts.

Maintain a safe distance from the crush zone.

4700903422
Warning - Crush zone, chip spreader (optional)

Risk of personal injury or being crushed.

Keep well clear of the spreader's working area

4700908229
Warning - Risk of crushing, apply locking device

The articulation must be locked when lifting.

Read the instruction manual.

4812125363
Warning - Locking during transport

The articulation must be locked during transport
and lifting,

but be open during operation.

Read the instruction manual.

4700791642
Warning - Starting gas

Starting gas is not to be used.

36

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments