manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 91 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 91

Operation

4812164601_C.pdf

2023-01-05

Driving

Operating the roller

12

32

2

6

3

1

Fig. Instrument panel
 1. Ignition key
 2. Throttle control
(D1703 / V2203-M-E3B)
 3. Emergency stop
 6. Forward/Reverse lever
 32. Engine speed selector
(D1803 / V2403-CR-E4B /V2403-CR-E5B)

Under no circumstances is the machine to be
operated from the ground. The operator must be
seated inside the machine during all operation.

Under no circumstances is the machine to be
operated from the ground. The operator must be
seated inside the machine during all operation.

Make sure that the area in front of and behind the
roller is clear.

Make sure that the area in front of and behind the
roller is clear.

Release the parking brake and check that the parking
brake lamp goes off.

D1703 / V2203-M-E3B (Stage IIIA)

Turn the throttle control (2) in backward position.

D1803 / V2403-CR-E4B (Tier 4f) /
V2403-CR-E5B (Stage V)

Press the LED button (32) so it is
in LOW mode (1 lamp lit).

Check that the steering is working correctly by turning
the steering wheel once to the right and once to the
left while the roller is stationary.

When compacting asphalt, remember to enable the
sprinkler system (12).

75

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments