Fayat DYNAPAC CC1400C Instruction Manual Download Page 63

Page: 63 / 239

Machine description

4812164601_C.pdf

2023-01-05

Function description, buttons on Forward /
Reverse lever

Mode / Button

LED

Button 1

Button 2

Button 3

Mode / Button

LED

Button 1

Button 2

Button 3

Transport mode

None

Edge cutter, up

Transport mode

None

Edge cutter, up

Working mode

Vibration, front

Vibration, rear

Edge cutter, up

Working mode

Vibration, front

Vibration, rear

Edge cutter, up

Edge cutter mode

Vibration, front

Edge cutter, down

Edge cutter, up

Edge cutter mode

Vibration, front

Edge cutter, down

Edge cutter, up

Spreader mode

Vibration, front

Spreader

Edge cutter, up

Spreader mode

Vibration, front

Spreader

Edge cutter, up

Right lever (RH)

Left lever (LH)

Machine with dual controls (option).

Fig. Double forward/reverse lever
1. Vibration on/off

Standard equipped machine.

Fig. Forward/Reverse lever right
1. Vibration on/off

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Search results

Summary of Contents for DYNAPAC CC1400C

Reviews:

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 63 / 239

Search results

Summary of Contents for DYNAPAC CC1400C

Reviews: