manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 92 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 92

Operation

4812164601_C.pdf

2023-01-05

Interlock/Emergency stop/Parking brake -
Check

The interlock, emergency stop and parking brake must
be checked daily before operating. A function check of
the interlock and emergency stop requires a restart.

The interlock, emergency stop and parking brake must
be checked daily before operating. A function check of
the interlock and emergency stop requires a restart.

The interlock function is checked by the operator
standing up from the seat when the roller is moving
very slowly forwards/backwards. (Check in both
directions). Hold the steering wheel firmly and brace
yourself for a sudden stop. A buzzer goes on and after
4 seconds the engine switches off and the brakes
are activated.

The interlock function is checked by the operator
standing up from the seat when the roller is moving
very slowly forwards/backwards. (Check in both
directions). Hold the steering wheel firmly and brace
yourself for a sudden stop. A buzzer goes on and after
4 seconds the engine switches off and the brakes
are activated.

Check the function of the emergency stop by pressing
the emergency stop when the roller is moving slowly
forwards/backwards. (Check in both directions). Hold
the steering wheel firmly and brace yourself for a
sudden stop. The engine switches off and the brakes
are activated.
If malfunction is detected during emergency stop
testing, replace it immediately with a new one.

Check the function of the emergency stop by pressing
the emergency stop when the roller is moving slowly
forwards/backwards. (Check in both directions). Hold
the steering wheel firmly and brace yourself for a
sudden stop. The engine switches off and the brakes
are activated.
If malfunction is detected during emergency stop
testing, replace it immediately with a new one.

Check the function of the parking brake by activating
the parking brake when the roller is moving very
slowly forwards/backwards. (Check in both
directions). Hold the steering wheel and brace yourself
for a sudden stop when the brakes are activated. The
engine does not switch off.

Check the function of the parking brake by activating
the parking brake when the roller is moving very
slowly forwards/backwards. (Check in both
directions). Hold the steering wheel and brace yourself
for a sudden stop when the brakes are activated. The
engine does not switch off.

76

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments