Home
/
Fayat
/
DYNAPAC CC1400C
/
Instruction Manual

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 106 / 239

Share

Page: 106 / 239

Fayat DYNAPAC CC1400C Instruction Manual Download Page 106

Miscellaneous

4812164601_C.pdf

2023-01-05

Towing the roller

Fig. Towing

The roller must be counter-braked during
towing/recovery. Always use a towbar. There is no
braking capacity on the roller now.

The roller must be counter-braked during
towing/recovery. Always use a towbar. There is no
braking capacity on the roller now.

The roller must be towed slowly, max. 3 kph (2
mph) and only towed short distances, max. 300 m
(1000 ft).

The roller must be towed slowly, max. 3 kph (2
mph) and only towed short distances, max. 300 m
(1000 ft).

When towing/retrieving a machine, the towing device
must be connected to both lifting holes. The pulling
force shall act longitudinally on the machine as shown
in the figure.

Maximum total pulling force:

- CC1100C VI / CC1200C VI 39 kN (9.767 lbf)

- CC1300C VI / CC1400C VI 63 kN (14.163 lbf)

Reverse the towing preparations.

Reverse the towing preparations.

Fig. Bracket, towing - front

Fig. Bracket, towing - rear

90

«
...
104
105
106
107
108
...
»

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments