manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 235 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 235

Maintenance, every 12th month (Annually)

4812164601_C.pdf

2023-01-05

Maintenance, every 12th month
(Annually)

Air cleaner
Check - Replacement of main filter

Replace the air cleaner's main filter when the
indicator shows red. The indicator is mounted on
the air cleaner's connecting pipe.

Replace the air cleaner's main filter when the
indicator shows red. The indicator is mounted on
the air cleaner's connecting pipe.

Air filter indicator - Resetting

1

Fig. Indicator
 1. Button

The air filter indicator is located on the filter,
or in its immediate vicinity.

The air filter indicator must be reset after replacing
the air filter.

Press the "button" (1) on the top of the indicator
to reset.

Backup filter - Change

Fig. Air filter
 1. Backup filter

1

Change the backup filter with a new filter after every
third replacement of the main filter.

To change the backup filter (1), pull the old filter out of
its holder, insert a new filter and reassemble the air
cleaner in the reverse order.

Clean the air cleaner if necessary.
See section Air cleaner - Cleaning.

219

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments