manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 60 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 60

Machine description

4812164601_C.pdf

2023-01-05

Machine alarm

Symbol

Designation

Function

Symbol

Designation

Function

Warning symbol, hydraulic fluid filter

If the symbol is shown when the diesel engine is running at
full speed, the hydraulic fluid filter must be changed.

Warning symbol, hydraulic fluid filter

If the symbol is shown when the diesel engine is running at
full speed, the hydraulic fluid filter must be changed.

Warning symbol, clogged air filter

If this symbol is shown when the engine is running at full
speed, the air filter must be checked/replaced.

Warning symbol, clogged air filter

If this symbol is shown when the engine is running at full
speed, the air filter must be checked/replaced.

Warning symbol, battery charging

If the symbol is shown when the engine is running, then
the alternator is not charging.
Switch off the engine and locate the fault.

Warning symbol, battery charging

If the symbol is shown when the engine is running, then
the alternator is not charging.
Switch off the engine and locate the fault.

Warning symbol, engine temperature

If this symbol is shown, the engine is too hot. Stop the
engine immediately and locate the fault.
Refer also to the engine manual.

Warning symbol, engine temperature

If this symbol is shown, the engine is too hot. Stop the
engine immediately and locate the fault.
Refer also to the engine manual.

Warning symbol, hydraulic fluid
temperature

If this symbol is shown, the hydraulic fluid is too hot.
Do not drive the roller; allow the fluid to cool by running the
engine on idle, and then locate the fault.

Warning symbol, hydraulic fluid
temperature

If this symbol is shown, the hydraulic fluid is too hot.
Do not drive the roller; allow the fluid to cool by running the
engine on idle, and then locate the fault.

Warning symbol, low fuel level

Less than 10% of the fuel is left if this symbol is shown.

Warning symbol, low fuel level

Less than 10% of the fuel is left if this symbol is shown.

Warning symbol, low sprinkler water
level

If this symbol is shown, there is less than 10% of the
sprinkler water left in the main tank.

Warning symbol, low sprinkler water
level

If this symbol is shown, there is less than 10% of the
sprinkler water left in the main tank.

Warning symbol, low oil pressure,
diesel engine

If this symbol is shown, the engine's oil pressure is too low.
Switch off the engine immediately.

Warning symbol, low oil pressure,
diesel engine

If this symbol is shown, the engine's oil pressure is too low.
Switch off the engine immediately.

Warning symbol, water in the fuel

If this symbol is shown, the engine must be stopped and
the fuel pre-filter drained of water.

Warning symbol, water in the fuel

If this symbol is shown, the engine must be stopped and
the fuel pre-filter drained of water.

44

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments