manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 167 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 167

Maintenance - 500h

4812164601_C.pdf

2023-01-05

Fig. Engine compartment, right side -
D1803-CR (Tier 4f / Stage V)
 1. Drainage hose
 2. Drain plug
 3. Filler cap
 4. Oil filter

1

3

2

4

Remove the oil filter (4).

Collect any spillage.

Install the new filter.

Fit the drain plug (2) to the end of the hose.

Fill with fresh engine oil. See under the heading
lubricants, for the correct oil grade. Fit the filler cap (3)
and check that the oil level is correct using the dipstick.

Start the engine and allow it to idle for a few minutes.
During this time, check around the oil filter and drain
plug for leaks.

Switch off the engine, wait for a minute or so and then
check the oil level. Top up with more oil if necessary.

4

3

2

Fig. Engine compartment right side -
V2203-M (Stage IIIA)
 2. Drain plug
 3. Filler cap
 4. Oil filter

2

3

4

Fig. Engine compartment right side -
V2403-CR (Tire 4f / Stage V)
 2. Drain plug
 3. Filler cap
 4. Oil filter

151

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments