manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 228 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 228

Maintenance, 3000h

4812164601_C.pdf

2023-01-05

Coolers
Checking - Cleaning

Fig. Engine compartment
(CC1100/C VI -  CC1200/C VI)
 1. Water cooler
 2. Hydraulic fluid cooler

2

1

Make sure that the air flow through the coolers (1) and
(2) is unobstructed. Dirty coolers are blown clean with
compressed air or washed clean using a
high-pressure water cleaner.

Blow air or direct water through the cooler in the
opposite direction to that of the cooling air.

Take care when using a high-pressure water jet.
Do not hold the nozzle too near the cooler.

Take care when using a high-pressure water jet.
Do not hold the nozzle too near the cooler.

1

2

Fig. Engine compartment
(CC1300/C VI -  CC1400/C VI)
 1. Radiator
 2. Hydraulic fluid cooler

Wear protective goggles
when working with
compressed air or
high-pressure water jets.

Wear protective goggles
when working with
compressed air or
high-pressure water jets.

212

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments