manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 117 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 117

Operating instructions - Summary

4812164601_C.pdf

2023-01-05

Operating instructions - Summary

1.

Follow the SAFETY INSTRUCTIONS specified in the Safety Manual.

1.

Follow the SAFETY INSTRUCTIONS specified in the Safety Manual.

2.

Make sure that all instructions in the MAINTENANCE section are followed.

2.

Make sure that all instructions in the MAINTENANCE section are followed.

3.

Turn the master switch to the ON position.

3.

Turn the master switch to the ON position.

4.

Set the emergency stop in the pulled out position.

4.

Set the emergency stop in the pulled out position.

5.

Move the forward/reverse lever to the NEUTRAL position.

5.

Move the forward/reverse lever to the NEUTRAL position.

6.

Set the engine speed control to 

MEDIUM.

 (

D1703 / V2203-M

).

6.

Set the engine speed control to 

MEDIUM.

 (

D1703 / V2203-M

).

Set the speed selector to 

LOW

 (

D1803 / V2403-CR

).

Set the speed selector to 

LOW

 (

D1803 / V2403-CR

).

7.

Start the engine and allow it to warm up.

7.

Start the engine and allow it to warm up.

8.

Set the engine speed control to the operating position.

8.

Set the engine speed control to the operating position.

9.

Drive the roller. Operate the forward/reverse lever with care.

9.

Drive the roller. Operate the forward/reverse lever with care.

10. Check the brakes, drive slowly. Remember that the braking distance will be

longer if the hydraulic oil is cold.

10. Check the brakes, drive slowly. Remember that the braking distance will be

longer if the hydraulic oil is cold.

11.

Use vibration only when the roller is in motion.

11.

Use vibration only when the roller is in motion.

12.

Check that the drums are thoroughly watered when watering is required.

12.

Check that the drums are thoroughly watered when watering is required.

13. IN AN EMERGENCY:

- Press the EMERGENCY STOP
- Hold the steering wheel firmly.
- Brace yourself for a sudden stop. The engine stops.

13. IN AN EMERGENCY:

- Press the EMERGENCY STOP
- Hold the steering wheel firmly.
- Brace yourself for a sudden stop. The engine stops.

14.

Parking: - Stop the engine and chock the drums.

14.

Parking: - Stop the engine and chock the drums.

15.

When lifting: - Refer to the relevant section in the Instruction Manual.

15.

When lifting: - Refer to the relevant section in the Instruction Manual.

16.

When towing: - Refer to the relevant section in the Instruction Manual.

16.

When towing: - Refer to the relevant section in the Instruction Manual.

17.

When transporting: - Refer to the relevant section in the Instruction Manual.

17.

When transporting: - Refer to the relevant section in the Instruction Manual.

18.

When recovering - Refer to the relevant section in the Instruction Manual.

18.

When recovering - Refer to the relevant section in the Instruction Manual.

101

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments