manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 229 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 229

Maintenance, 3000h

4812164601_C.pdf

2023-01-05

Water tank - Draining

1

Fig. Water tank
1. Drain plug

Remember that there is a risk of freezing during
the winter. Empty the tank, pump and lines.

Remember that there is a risk of freezing during
the winter. Empty the tank, pump and lines.

Remove the drain plug (1) and allow all the water to
run out. Wipe clean the drain plug and screw back in.

1

Fig. Water tank
 1. Drain plug

Water tank - Cleaning

Clean the tank with water and a suitable detergent for
plastic surfaces.

Refit the filter housing or the drain plug (1).
Fill with water and check for leaks.

The water tank is made of plastic (polyethylene)
and are recyclable.

The water tank is made of plastic (polyethylene)
and are recyclable.

Checking - Diesel engine valve clearance

Contact your local Kubota representative
for this service

213

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments