manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 119 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 119

Preventive maintenance

4812164601_C.pdf

2023-01-05

Preventive maintenance

Complete maintenance is necessary for the machine
to function satisfactorily and at the lowest
possible cost.

The Maintenance section includes the periodic
maintenance that must be carried out on the machine.

The recommended maintenance intervals assume that
the machine is used in a normal environment and
working conditions.

Acceptance and delivery inspection

The machine is tested and adjusted before it leaves
the factory.

On arrival, before delivery to the customer, delivery
inspection must be conducted as per the check list in
the warranty document.

Any transport damage must be reported immediately
to the transport company, as this is not covered by the
product warranty.

Warranty

The warranty is only valid if the stipulated delivery
inspection and the separate service inspection have
been completed as per the warranty document, and
when the machine has been registered for starting
under the warranty.

The warranty is not valid if damage has been caused
by inadequate service, incorrect use of the machine,
the use of lubricants and hydraulic fluids other than
those specified in the manual, or if any other
adjustments have been made without
the requisite authorization.

103

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments