Fayat DYNAPAC CC1400C Instruction Manual Download Page 64

Page: 64 / 239

Machine description

4812164601_C.pdf

2023-01-05

Speed adjustment and vibration frequency
(CC1100/C VI - CC1400/C VI
with single amplitude)

Fig. Mechanical speed control
1. Control in idle mode
2. Control in center position / ECO
3. Control in lowermost position

Mechanical speed control

If the speed control is in the center position / ECO (2),
both the engine speed and vibration frequency are low.

If the speed control is in the lowermost
position / ECO (3), both the engine speed
and vibration frequency are high.

Fig. Electronic speed control
1. LED lamp for
Low speed / frequency (ECO)
2. LED lamp for High speed / frequency

Electronic speed control

If the LED lamp in the center is lit green (ECO),

Low

engine speed and

low

vibration frequency

are selected.

If the LED lamp to the right is lit red,

High

engine

speed and

high

frequency are selected.

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Search results

Summary of Contents for DYNAPAC CC1400C

Reviews:

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 64 / 239

Search results

Summary of Contents for DYNAPAC CC1400C

Reviews: