manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 179 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 179

Maintenance - 1000h

4812164601_C.pdf

2023-01-05

Maintenance - 1000h

Performed after 1000 operating hours (each year)

Park the roller on a level surface.
The engine must be switched off and the
parking brake activated when checking or
adjusting the roller, unless otherwise specified.

Park the roller on a level surface.
The engine must be switched off and the
parking brake activated when checking or
adjusting the roller, unless otherwise specified.

Ensure that there is good ventilation (air
extraction) if the engine is run indoors.
Risk of carbon monoxide poisoning.

Ensure that there is good ventilation (air
extraction) if the engine is run indoors.
Risk of carbon monoxide poisoning.

Battery
- Check condition

Fig. Battery

The battery is sealed and maintenance-free.

Make sure there is no open flame in the vicinity
when checking the electrolyte level. Explosive gas
is formed when the alternator charges the battery.

Make sure there is no open flame in the vicinity
when checking the electrolyte level. Explosive gas
is formed when the alternator charges the battery.

When disconnecting the battery, always
disconnect the negative cable first. When
connecting the battery, always connect the
positive cable first.

When disconnecting the battery, always
disconnect the negative cable first. When
connecting the battery, always connect the
positive cable first.

The cable shoes should be clean and well-tightened.
Corroded cable shoes should be cleaned and greased
with acid-free Vaseline.

Wipe the top of the battery.

163

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments