manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 231 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 231

Maintenance, 3000h

4812164601_C.pdf

2023-01-05

Draining of water separator

1

Fig. Fuel filter
 1. Filter knob
 2. Filter element
 3. OFF
 4. ON

2

3

4

Close the fuel filter knob (1).

Remove the top cap and rinse the inside
with diesel fuel.

Remove filter element (2) and rinse the inside
with diesel fuel.

After cleaning, install the fuel filter, to keep out
of dust and dirt.

Air-bleed the injection pump.

Dust and dirt may cause a injection pump and
nozzle failure. Wash the fuel filter cup periodically.

Dust and dirt may cause a injection pump and
nozzle failure. Wash the fuel filter cup periodically.

Fig. Fuel filter element
 5. O-ring
 6. Filter element
 7. Spring
 8. Filter
 9. Screw ring

5

6

7

8

9

5

Replacing belts/Checking the belt tension

215

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments