manualshive.com logo in svg

Fayat DYNAPAC CC1400C, Instruction Manual, Page: 137 / 239

Share
Download
Fayat DYNAPAC CC1400C Instruction Manual Download Page 137

Maintenance, 10h

4812164601_C.pdf

2023-01-05

Fig. Engine  - D1703 (Stage IIIA)
 1. Dipstick
 2. Filler cap

1

2

Open the engine cover lock and lower the engine
cover forwards.

Check the oil level using the dipstick (1). The level
should be between the marks. If the level is near the
lower mark, top off with fresh engine oil via the filler
cap (2). See under the heading lubricants for the
correct oil grade.

Never overfill with oil, as this can damage
the engine.

Never overfill with oil, as this can damage
the engine.

1

2

Fig. Diesel engine -
D1703 (Tier 4f / Stage V)
 1. Dipstick
 2. Filler plug

Fig. Diesel engine -
D1803 (Tier 4f / Stage V)
 1. Dipstick
 2. Filler plug

1

2

1

2

Fig. Diesel engine -
V2203-M (Stage IIIA)
 1. Dipstick
 2. Filler plug

1

2

Fig. Diesel engine -
V2403-CR (Tier 4f / Stage V)
 1. Dipstick
 2. Filler plug

121

Summary of Contents for DYNAPAC CC1400C
















































































































































































































































Reviews:

No comments