Fargo DTC4500e Service Manual Download Page 26

Page: 26 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 26

DTC4500e Lamination Module Cover Removal

NOTE:

Remove the Lamination Module prior to removing the printer covers if repairing the PRINTER. The

Lamination Module does not need to be removed in order to repair the Lamination Module (unless replacing
the Lamination Mainboard).

Step Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Remove the card output bin (D930296-01)

Remove the Input Bump Cover (D930292-02)

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 15 minutes

Preparation:

Important:

This procedure can only be performed by

authorized service personnel.

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands