manualshive.com logo in svg

Fargo DTC4500e, Service Manual

The Fargo DTC4500e is a reliable and high-quality card printer suitable for a variety of organizations. For easy setup and operation, make sure to download the free User Manual from manualshive.com. This manual provides detailed instructions for maximizing the features of your Fargo DTC4500e.

Share
Download
background image

 

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual  PLT-01543 rev 1.0 

 

November  2013                                                                                                                                    51 

. 

 

 

Step  Procedure    

4 

Rotate the Lift Bracket (D930136) with the spring (D930266) upwards to disengage the hinge.   

 

   5 

Lift out the Pinch Roller Bracket (D930137).  

 

NOTE:

 Verify orientation when re installing. 

 

   6 

Replace with new Platen Roller. 

 Lock platen with cam first into the front sideplate. 

Summary of Contents for DTC4500e


















































































































































Reviews:

No comments

Related manuals for DTC4500e

Canon IMAGEPRESS C7010VPS Brochure & Specs preview
IMAGEPRESS C7010VPS
Brand: Canon Pages: 4
Canon iP2600 - PIXMA Color Inkjet Printer Setup Instructions preview
iP2600 - PIXMA Color Inkjet Printer
Brand: Canon Pages: 2
Canon FAXPHONE L80 Setup Instructions preview
FAXPHONE L80
Brand: Canon Pages: 8
Canon ImageCLASS 2300 Network Manual preview
ImageCLASS 2300
Brand: Canon Pages: 102
Canon ImageCLASS MF4570dw Basic Operation Manual preview
ImageCLASS MF4570dw
Brand: Canon Pages: 164
Canon imagePRESS C800 Series Service Manual preview
imagePRESS C800 Series
Brand: Canon Pages: 132
Canon ImageCLASS MF5730 Technical Information preview
ImageCLASS MF5730
Brand: Canon Pages: 2
QMS 2001 Setup Manual preview
2001
Brand: QMS Pages: 26
F+D Feinwerk- und Drucktechnik Plus Software Manual preview
Plus
Brand: F+D Feinwerk- und Drucktechnik Pages: 41
Canon MP490 series Getting Started preview
MP490 series
Brand: Canon Pages: 32
Lexmark C910 Finisher Manual preview
C910 Finisher
Brand: Lexmark Pages: 11
Zonestar Z8PM4 Pro User Manual preview
Z8PM4 Pro
Brand: Zonestar Pages: 25
ABLE Ap1400 Programmer'S Manual preview
Ap1400
Brand: ABLE Pages: 42
Olivetti d-COLOR MF3800 Manual preview
d-COLOR MF3800
Brand: Olivetti Pages: 82
Aficio dsc424 Operating Instructions Manual preview
dsc424
Brand: Aficio Pages: 156
Weber Markoprint X4JET Manual For Installation, Operation And Maintenance preview
Markoprint X4JET
Brand: Weber Pages: 177
Ithaca PcOS Series 80PLUS Programmer'S Manual preview
PcOS Series 80PLUS
Brand: Ithaca Pages: 131
Star Micronics SP200 Series User Manual preview
SP200 Series
Brand: Star Micronics Pages: 127

Brands by name

Popular brands

Load more brands