Fargo DTC4500e Service Manual Download Page 55

Page: 55 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 55

Remove/Replace the Cleaning Roller (D930121), Input Feed Lever (D930132),

Input Lever Gear (D930164)

Step

Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Remove the ribbon supply assembly.

Remove the mainboard (D930500)

Remove the screw F000178 & washer 140040 from the motor assembly. This is done from the
front of the printer.

NOTE:

This step is used for the DTC 1250e, 1000Me, 4250e

Slide the Supply Spindle DOWN To release. Slide the Motor UP to install.

NOTE:

You do not need to remove the gears or the Stepper Motor for this procedure.

D930121

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 30 min

Preparation:

Remove the Covers

Important:

This procedure can only be performed by

authorized service personnel.

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands