Fargo DTC4500e Service Manual Download Page 84

Page: 84 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 84

Remove/Replace the Flipper Assembly Stepper Motor

– E001192

Step Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Remove the Flipper Covers.

Disconnect the cable (D930610) from J5 on the PCB.

If replacing this cable make

NOTE:

of how the wire is routed.

Remove the 2 screws (F000178) that hold the motor to the frame.

Replace with new motor

Procedure is complete

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 20 min

Preparation:

Remove the Covers

Important:

This procedure can only be performed by

authorized service personnel.

Stepper Motor Cable (D930610)

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands