Fargo DTC4500e Service Manual Download Page 85

Page: 85 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 85

Remove/Replace the Headlift Sensor/Cable- D900113

Step Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Remove the Flipper Covers.

Pull the Headlift Sensor OUT towards the stepper motor gear to release from the frame. Sensor does
not come out with breaking the sensor or tab.

Replace sensor by snapping IN the slot provided.

Reverse assembly

Procedure is complete

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 20 min

Preparation:

Remove the Covers

Important:

This procedure can only be performed by

authorized service personnel.

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands