Fargo DTC4500e Service Manual Download Page 90

Page: 90 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 90

Remove/Replace the Lamination Head Assembly

Upper Assembly (D920022) & Lower Assembly (D920023)

Step Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Both the Upper and Lower Lamination Assemblies follow the same procedure.

This part is sold as one assembly which
includes :

Platen Roller (D920012-Upper),

Lamination Roller (D920020- Lower),

Film LED (A000454)

Head Lift Sensor (A000126)

Thermocouple RTD/cable (D920151)

Motor (D900484-05) and the wires.

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 35 min

Preparation:

Remove the Lamination Module Covers.

Remove the mainboard to access the wire removal procedure.

Important:

This procedure can only be performed by

authorized service personnel.

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands