Fargo DTC4500e Service Manual Download Page 68

Page: 68 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 68

Step

Procedure

Remove the screw F000178 & washer 140040 from the Stepper Motor assembly. This is done from
the front of the printer.

NOTE:

DTC1250e/4250e will have 2 screws holding the Supply. DTC4500e has only one screw

holding the supply.

Slide the Supply Spindle DOWN To release. Slide the Motor UP to install.

NOTE:

You do not need to remove the gears or the Stepper Motor for this procedure.

NOTE:

If ribbon wrinkle occurs after replacing the motor, move the motor assembly DOWN slightly in

the frame. Loosen the 2- F000178 screws from the supply spindle, move down 1/16

inch then

tighten the F000178 screws.

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands