Fargo DTC4500e Service Manual Download Page 60

Page: 60 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 60

Remove/Replace Ribbon Take-Up Motor (D930014)

Step Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Remove the screw (F000178) & washer (140040) from the motor assembly.

This is done from the front of the printer.

Slide the Take-Up Motor DOWN to release. Slide the Motor UP to install.

NOTE::

You do not need to remove the gears or the Stepper Motor for this procedure.

D930014

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 20 min

Preparation:

Remove the Covers

Important:

This procedure can only be performed by

authorized service personnel.

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands