Fargo DTC4500e Service Manual Download Page 8

Page: 8 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 8

Cover Removal Procedures

Remove/Replace Printer Covers DTC 1000Me- 1250e Single Side

Step Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Open the front door. Locate and remove the 2 screws. (F000178)

Lift up the top cover and disconnect the display cable (D930607) from the mainboard.

Remove the top cover by flexing the center to disengage the insert tabs.

DTC1250e single side shown

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 15 minutes

Preparation:

Important:

This procedure can only be performed by

authorized service personnel.

DTC1250e DTC1000Me

Top Cover/PCB Assy D930034-02 D930034-02

Front Door D930265-05 D930265-04

Left Cover D930263-03 D930263-02

Right Cover D930264-03 D930264-02

Output Bin D930269-01 D930269-01

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands