Fargo DTC4500e Service Manual Download Page 59

Page: 59 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 59

Step Procedure

Slide the Supply Spindle DOWN To release. Slide the Motor UP to install.

NOTE:

You do not need to remove the gears or the Stepper Motor for this procedure.

NOTE:

If ribbon wrinkle occurs after replacing the motor, move the motor assembly DOWN slightly in

the frame. Loosen the 2- F000178 screws from the supply spindle, move down 1/16

inch then

tighten the F000178 screws.

Remove the RFID cable (D930603) from the Supply Spindle.

Remove the Encoder Sensor cable harness (D930600) from the encoder sensor.

NOTE:

The routing of these wires under the clip.

Replace the complete assembly Motor.

Reconnect wires.

Procedure is complete.

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands