manualshive.com logo in svg

Fargo DTC4500e, Service Manual

The Fargo DTC4500e is a reliable and high-quality card printer suitable for a variety of organizations. For easy setup and operation, make sure to download the free User Manual from manualshive.com. This manual provides detailed instructions for maximizing the features of your Fargo DTC4500e.

Share
Download
background image

 

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual  PLT-01543 rev 1.0 

 

November  2013                                                                                                                                    49 

. 

 

 

Step  Procedure    

  6 

Remove the print head assembly if better access is needed. 

See Printhead removal procedure

 Replacing the DTC Printhead

.  

  7 

Move the lever up to clear the Platen Roller (D930120) 

               

 

  8 

Replace with new roller.  

  9 

Reverse assembly to reinstall parts.   

  10 

Procedure is complete. 

Summary of Contents for DTC4500e


















































































































































Reviews:

No comments

Related manuals for DTC4500e

NCR 7197 Owner'S Manual preview
7197
Brand: NCR Pages: 5
Pantum P2200 Series Maintenance Manual preview
P2200 Series
Brand: Pantum Pages: 105
GCC Technologies Elite 12N Network Manual preview
Elite 12N
Brand: GCC Technologies Pages: 63
gCreate gMax 2 PRO Unboxing And Setup Instructions preview
gMax 2 PRO
Brand: gCreate Pages: 9
GCC Technologies Elite XL-1208 Supplementary Manual preview
Elite XL-1208
Brand: GCC Technologies Pages: 9
GCC Technologies Elite XL-1208 Install Manual preview
Elite XL-1208
Brand: GCC Technologies Pages: 12
gCreate gMax 2 PRO User Manual preview
gMax 2 PRO
Brand: gCreate Pages: 21
GCC Technologies Elite XL User Manual preview
Elite XL
Brand: GCC Technologies Pages: 199
Xerox DocuColor 6060 Recommended Materials List preview
DocuColor 6060
Brand: Xerox Pages: 4
Lexmark 7016-630 Service Manual preview
7016-630
Brand: Lexmark Pages: 455
Tally T6090 Maintenace Manual preview
T6090
Brand: Tally Pages: 202
zortrax Inkspire Packing preview
Inkspire
Brand: zortrax Pages: 11
Ricoh Aficio 1018 Operating Instructions Manual preview
Aficio 1018
Brand: Ricoh Pages: 74
idp SMART-30S User Manual preview
SMART-30S
Brand: idp Pages: 88
Xerox WorkCentre 6400XF Evaluator Manual preview
WorkCentre 6400XF
Brand: Xerox Pages: 24
Oki CX3535 Safety Information Manual preview
CX3535
Brand: Oki Pages: 64
Ultimaker Heated Bed Upgrade Kit Assembly Manual preview
Heated Bed Upgrade Kit
Brand: Ultimaker Pages: 37
HandTop HT3020UV-C-K Operation Manual preview
HT3020UV-C-K
Brand: HandTop Pages: 97

Brands by name

Popular brands

Load more brands