Fargo DTC4500e Service Manual Download Page 34

Page: 34 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 34

Remove/Replace the Display Assembly (MDP-00093 DTC4250e/4500e)

(MDP-00059 DTC1250e)

Contains Cover, PCB, LCD Buttons and Cable

The same procedure is used for either orientation of the LCD Display.

Step

Procedure

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Remove the top cover of the printer.

Pull forward on the display to un-snap from the bottom of the display. Lift out to remove.

Remove the ribbon cable (D930607)

(Also from the LCD PCB A930507-01-DTC4250e/4500e).

MDP-00093

MDP-00059

Tools needed:

T10 Torx screwdriver

Estimated Repair Time: 15 min

Preparation:

Remove Top Cover

Important:

This procedure can only be performed by

authorized service personnel.

LCD PCB (board only) DTC4250e 4500e A930507-01

LCD PBC (board only) DTC 1250e A930507

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands