Fargo DTC4500e Service Manual Download Page 112

Page: 112 / 145

DTC1000Me-1250e-4250e-4500e Card Printer Service Manual PLT-01543 rev 1.0

November 2013 112

DTC Printhead procedure

The guide serves to instruct the user about replacing the Printhead. This procedure can only be
performed by authorized service personnel.

Caution:

Turn OFF the Printer and unplug the power cord from the Printer.

Danger:

Wear proper eye protection to perform the procedures in this section.

Reverse the disassembly steps to reassemble the Card Printer. ESD precautions are
necessary when handling electronics assemblies.

Step Procedure
1

Caution: Turn OFF the Printer and unplug the power cord from the Printer.

Turn the printer over to access the Headlift cover.

Tools needed:

Flathead screwdriver

Torx Wrench (included in kit)

Estimated Repair Time: 20 minutes

Preparation:

Remove Printhead mount

Important:

This procedure can only be performed by

authorized service personnel.

Make

NOTE:

of the resistance value on the new

printhead; verify this value in the Advanced Settings
driver option. Refer to the User Guide for more
information.

Summary of Contents for DTC4500e


















































































































































Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands

Fargo DTC4500e, Service Manual

Search results

Summary of Contents for DTC4500e

Reviews:

Related manuals for DTC4500e

Brands by name

Popular brands