manualshive.com logo in svg

Fagor ACSD series, Original Instructions Manual

Share
Download
Fagor ACSD series Original Instructions Manual Download Page 75

Digital Brushless 

AC S

ervo 

D

rive system - Ref.1609

ACSD-75/80

Motor not accepted by the drive.
Motor's power voltage is different from that of the drive (e.g.: motor FXM34.40

A

.E1.000

with MCP-20

L

 drive).

Some of the sine or cosine signals of the encoder has reached a peak level lower than
150 mV.

Contact Fagor Automation.

The drive has not detected the rotor sensor. 
Match the selected sensor with the feedback installed.
Contact Fagor Automation.

Communication error when using a SinCos or SinCoder encoder.
Incoherent U, V, W signals when using an incremental I0 encoder. 
Contact Fagor Automation.

Contact Fagor Automation.

  E.510 

Incoherent combination of motor and feedback

  E.605 

Excessive damping of the analog signals of the motor 
feedback.

  E.801

Encoder not detected

  E.802

Defective encoder

  E.803

Encoder not initialized

+ 0.15 V

- 0.15 V

Summary of Contents for ACSD series



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands