XTP CrossPoint Series • Programming Guide
112
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Save and directly write global presets
Save current configuration as a
global preset
E
S
X#
PRST
}
PrstS
X#]
Example:
E
S8PRST
}
PrstS08
]
Save current ties as preset 8.
Direct write process —
NOTE:
The direct write of a global preset should always be preceded by a clear global preset ties command of that same preset number,
as shown below. In a directly-written preset, the input for each output position (or no tied input) remains unchanged unless overwritten
or cleared.
If you do not
clear
the ties in a global preset number before you directly
write
a global preset to that number, ties that are part of the
previous version of the specified preset with the same number can unexpectedly become part of the newly-created preset.
Clear global preset ties
E
+
X#
P0*!
}
Spr
X#]
Clear all ties in preset
X#
.
Directly write a global preset
E
+
X#
P
X!
*
X@
!
X!
*
X@
%
X!
*
X@
$
...
X!
*
X@
&
}
Enter as many ties as are valid. The
tie
all
(
!
),
tie RGB
(
&
),
tie video
(
%
), and
tie audio
(
$
) commands are all valid.
Spr
X#]
Example:
E
+27P0*!
}
Spr27
]
Clear all ties in preset 27.
Esc
+27P12*5!10*09%3*2$3*8&
Brackets are shown to separate ties for
clarity only. Create global preset 27,
which ties video and audio input 12 to
output 5, video input 10 to output 9,
audio input 3 to output 2, and video
input 3 to output 8.
Spr27
]
Resets
Reset global presets and names
E
ZG
}
Zpg
]
Clear all global presets and their names.
Reset
one
global preset
EX#
ZG
}
Zpg
X#]
Clear global preset
X#
.
Reset audio input levels
E
ZA
}
Zpa
]
Reset all audio input levels (gain and
attenuation) to 0 dB.
Reset audio output levels
E
ZV
}
Zpv
]
Reset all audio output levels (volume)
to 100% (no attenuation).
Reset whole matrix switcher
E
ZXXX
}
Zpx
]
Clear all ties and presets, reset all audio
gains to 0 dB, and reset volume to 100%.
NOTE:
The reset whole matrix switcher (
E
ZXXX
}
) command resets not only the matrix switcher, but any connected endpoints.
Absolute reset, including IP settings
E
ZQQQ
}
Zpq
]
Similar to
Reset whole matrix
switcher
, plus clear the IP address to
192.168.254.254 and subnet mask to
255.255.000.000.
NOTE:
The absolute reset (
E
ZQQQ
}
) command resets not only the matrix switcher, but any connected endpoints.
Absolute reset, excluding IP settings
E
ZY
}
Zpy
]
Similar to
Absolute reset, including
IP settings
(
E
ZQQQ
}
), but excludes
the following IP settings: IP address,
subnet mask, gateway address,
unit name, DHCP setting, and port
mapping (telnet, Web, and direct
address).
NOTES:
The absolute reset (
E
ZY
}
) command:
•
Preserves communications with the device and is recommended after a firmware update.
•
Resets not only the matrix switcher, but any connected endpoints.
NOTE:
X!
= Input number
00
–
16
or
32
(
00
= untied)
X@
= Output number
01
–
16
or
32
X#
= Global preset number
00
–
32
(
00
= current configuration, applies to view ties command only)
