XTP CrossPoint Series • Programming Guide
93
Command Function
SIS Command
(Host to Unit)
Response
(Unit to Host)
Additional Description
Inputs on XTP CP 4i [XTP] and XTP CP 4i 4K [XTP] Boards
XTP power
ATTENTION
:
•
Power over XTP (PoX) is intended for indoors use only. No part of a network that uses PoX can be routed outdoors.
•
PoX est destiné à une utilisation en intérieur uniquement. Aucune partie d’un réseau qui utilise PoX ne peut être routée en extérieur.
NOTE:
•
PoX is supplied by the XTP CrossPoint 48 V power supply.
•
XTP CrossPoint 1600:
•
Can power up to 28 total (input and output) endpoints at up to 364 watts.
•
Is available with optional 48 V power supply redundancy.
•
XTP CrossPoint 3200:
•
Can power up to 24 total (input and output) endpoints at up to 312 watts.
•
No 48 V power supply redundancy is available.
Enable or disable power to input
endpoint and report status
E
I
X^
*
X2@
POEC
}
PoecI
X^
*
X2@
*
X2#
*
X2$]
Enable or disable (
X2@
) remote power to
input
X^
. The endpoint is requesting
X2#
watts and the power status is
X2$
.
Example:
E
I1*1POEC
}
PoecI01*1*13*1
]
Enable remote power on input 1, which
is requesting 13 watts. The board is
providing power to the endpoint.
View input power status
E
I
X^
POEC
}
X2@
*
X2#
*
X2$]
Enable or disable input power and
report status, all inputs
E
I
X2@
*POEC
}
PoecI00*
X2@
1
X2@
2
...
X2@
n
]
Each
X2@
is the enable or disable status of
an input, starting at 1.
n
is 16 or 32.
View input power status, all inputs
E
IPOEC
}
X2@
1
X2@
2
X2@
3
...
X2@
n
]
View XTP power usage
E
TPOEC
}
X2%
*
X2^]
Show PoX wattage applied and the
status of the 48 V power supply.
Inputs on XTP CP 4i 3G Boards
AES digital audio channel selection
NOTE:
Eight-channel audio is divided into two groups, each
consisting of two channel pairs (four channels). The table at
right shows the channels contained within each group.
Group 1
Group 2
Ch Pair 1
Ch Pair 2
Ch Pair 1
Ch Pair 2
Ch 1 Ch 2 Ch 1 Ch 2 Ch 1 Ch 2 Ch 1 Ch 2
Select channel
E
I
X^
*
X2&
AESC
}
AescI
X^
*
X2&]
Select digital audio channel pair on
which audio will be embedded.
View selected channel
E
I
X^
AESC
}
X2&]
AES digital audio group selection
Select group
E
I
X^
*
X2*
AESG
}
AesgI
X^
*
X2*]
Select digital audio channel group on
which audio will be embedded.
View selected group
E
I
X^
AESG
}
X2*]
NOTE:
X^
= Input number (for other than tie)
01
–
16
or
32
X2@
= Enable or disable for power
0
= Disable (
default
)
1
= Enable
X2#
= Amount of power requested
00
or
13
(watts)
X2$
= Power status
0
= Unpowered endpoint
2
= Power available, disabled
4 = Fault
1
= Power provided to endpoint
3
= No power available, enabled
X2%
= Wattage
Power usage in
0.1
watt increments. Example:
260
= 26.0 watts
X2^
= Power supply status
0
= Ok
1
= Not Ok
X2&
= AESC digital channel pair
1
(
default
) or
2
X2*
= AESG digital channel group
1
(
default
) or
2
