Esco MAW-4D User Manual Download

Page: 95 / 101

Multi-zone ART Workstation User Manual Rev. 6.0

gas outlet with 0.6

–

1.0 atm above ambient if the clinic uses reduced oxygen

levels.

Tubes that fit 4 mm hose nipple and HEPA filter.

10.

Access to a PC with USB for the data logging.

34.3 Preparing for installation

•

Bring the

"Installation report"

form. Make sure it is the latest and current version

only.

•

Fill out the following blank boxes in the form: the Multi-zone ART Workstation
serial number (S/N) and customer.

•

The service tool kit is checked for content before every installation trip to ensure
it contains the necessary tools.

•

Always bring the latest versions of firmware and data logging software. Bring
these files on a labeled memory stick to the service site.

34.4 Bring the following to the installation site

•

"Installation report" form.

•

Service manual for the Multi-zone ART Workstation.

•

Updated service tool kit.

•

Memory stick with the latest released firmware & software.

•

High precision thermometer with a resolution not less than 0.1 °C.

•

Calibrated gas analyzer with precision at least 0.1% for CO

and O

•

Extension cable for USB connection.

34.5 Installation procedure at the site

Lift the cabinet using a stacker or forklift

Figure 34.1

Multi-zone ART Workstation, cabinet

Summary of Contents for MAW-4D






































































































Search results

Summary of Contents for MAW-4D

Reviews:

Related manuals for MAW-4D

Brands by name

Popular brands

Esco MAW-4D, User Manual

Search results

Summary of Contents for MAW-4D

Reviews:

Related manuals for MAW-4D

Brands by name

Popular brands