manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 91 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 91

ER5000

 — 

91

Installation Variations

Setpoint Wiring Variations

Digital Setpoint Source  — RS485 Network, RS232 

to RS485 Converter

 (TESCOM™ Model #85061)

The USB protocol isn’t networkable, so applications requiring 
multiple controllers must use RS485. RS485, wired through a 
converter as shown in Figure 29, allows for up to 32 ER5000s to be 
daisychained in a network. 

 WARNING

The controller must be disconnected from the power supply before 
any additional wiring or change to jumper configuration is 
performed. Do not reconnect the power supply until all additional 
wiring connections have been made and are properly installed.

(continued next page)

GRAY

GRAY

GRAY

- RS485

+24 V DC

+ RS485

GROUND

GREEN

GREEN

GREEN

VIOLET

VIOLET

VIOLET

BLUE

BLUE

BLUE

Figure 29: Multiple Controllers in an RS485 Network (RS232 to RS485 Converter)

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments