Emerson Tescom ER5000 Series User Manual Download Page 189

Page: 189 / 248

ER5000

—

189

The ERTune™ Program: Power User

The Additional ER Settings Panel

External Feedback Source

This field controls which feedback source displays in the Plot
Screen when you have wired the ER5000 for multiple feedback
sources. Refer to

Switch Feedback Control to a Second Feedback

Source

for an example of this wiring configuration.

•

External Feedback

is the transducer connected to the ER5000

through the orange wire (J3 Pin 3).

•

Extra Input #1

is the transducer connected to the ER5000

through the brown/white wire (J4 Pin 1).

To switch the external feedback source

1. Click the radio button next the source you wish to track.

IMPORTANT!

Refer to the steps

To change the display of the main

(left) axis to the new range

after you change the feedback source, to

be sure the ERTune™ program is tracking the correct range of values
for the new source.

Setpoint to 0 on Power Up

The ER5000 stores the last registered setpoint when it powers
down and powers up at the setpoint stored in internal memory.
Some applications may require a zero-pressure startup. This field
allows you to set that default for the controller.

To enable Setpoint to 0 on Power Up

1. Click the

Enable

radio button.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Search results

Summary of Contents for Tescom ER5000 Series

Reviews:

Emerson Tescom ER5000 Series, User Manual, Page: 189 / 248

Search results

Summary of Contents for Tescom ER5000 Series

Reviews: