manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 244 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 244

ER5000

 — 

244

Setting up the ERTune™ Program on Windows 8 PCs

9.  Select the 

.NET Framework 3.5

 check box. You do not need to 

select the child items for 

Windows Communication Foundation 

(WCF) HTTP activation

 unless you are a developer who requires 

WCF script and handler mapping functionality.

  

10.  Click

 OK.

Installing the ER5000 Device Driver

When loading the ER5000 USB Serial Port driver onto Windows 8 
you may encounter the following error message:

Windows found driver software for your device but encountered 

an error while attempting to install it. 
The third-party INF does not contain digital signature information.

 

Windows 8 has a Driver Signature Enforcement (DSE) feature. This 
feature allows the PC administrator or the user who is installing 
the Windows-based software, to know whether a legitimate 
publisher has provided the software package. 

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments