manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 134 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 134

 

ER5000

 — 

134

The ERTune™ Program: Basic Features

The Plot Screen Menu Bar

The Plot Screen Menu Bar displays two menus and two buttons.

The Plot Screen Menus — The Main Axis Menu

The commands in this menu control the main (left) vertical and 
horizontal axes of the display.

Time

This command allows you to set the number of seconds in one 
cycle of the Plot Screen. The default value is 10 seconds. The 
maximum cycle time is 1,000 seconds.

Minimum Vertical

This command allows you to set the minimum value of the 
main axis. The default value is 0 or the minimum of the current 
feedback range.

Maximum Vertical

This command allows you to set the maximum value of the main 
axis. The default value is 100 or the maximum of the current 
feedback range.

Rescale Vertical

This command resets the main axis to its original minimum and 
maximum values if they have been changed by the Maximum 
Vertical and/or Minimum Vertical commands. 

The Plot Screen Menus — The Secondary Axis Menu

The commands in this menu control the secondary (right) axis of 
the display. This axis tracks the optional additional variables and 
displays independently from the main axis. It is not affected by 
changes to the main axis.

NOTE

NOTE

CAUTION

CAUTION

WARNING

WARNING

The secondary axis appears if you add the optional third variable 

(green line) to the Plot Screen using 

The Plot Screen Variable Controls

. 

The range for this axis is set when you follow the steps 

To set or change 

the range for an added variable

.

The secondary axis does not display the range of the optional fourth 
variable (black line) which can be added using 

The Plot Screen Variable 

Controls

. This variable will be tracked within the scope of the range for 

the third variable.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments