manualshive.com logo in svg

Emerson Tescom ER5000 Series, User Manual, Page: 199 / 248

Share
Download
Emerson Tescom ER5000 Series User Manual Download Page 199

 

ER5000

 — 

199

ER5000 Software Development Support

Accessing the Windows DLL File

The TESCOM™ protocol, ER5000DLL.dll, allows easy access to the 
ER5000 from a PC for Windows based programs. The protocol is 
available as a 32-bit DLL (Dynamic Link Library). The DLL downloads 
to the PC as part of the ERTune™ program installation and can also 
be found in the ER5000 Software.

To locate and use the Windows DLL file

1.  Download the ER5000 Software and Manual file which can 

be found at TESCOM.com under the “Download ER5000 
Software and Manual” link. Once the file is downloaded, 
extract the zip file, click on the .exe file, and the ER5000 User 
Support Software and Manual menu will open. 

 

2.  The ER5000 User Support Software and Manual menu gives 

you access to the programs and reference materials. Click 
the 

Resources

 button. 

3.  Click the 

ER5000DLL

 button. This opens the folder that 

contains the 

ER5000DLL.dll 

file. You can open the file or save it 

to a location that is accessible to the custom program being 
developed.

Summary of Contents for Tescom ER5000 Series

























































































































































































































































Reviews:

No comments